Terminal block generator cross-platform (Page 2 of 6)

Thank you,

but I see à minor problem : hotspot size is smaller than the element and when you move element cause a lot of artifacts.

I need to open element in element editor for recalculate hotspot (automatic with save) element width=" " height=" " is wrong.

xml = ['<definition hotspot_x="4" hotspot_y="4" width="%i" height="%i" orientation="dyyy" link_type="simple" type="element">' \
               %(totalWith, max( TB_HEIGHT, TB_HEIGHT )),

I think is :  %(totalWith, max( TB_WIDTH, TB_HEIGHT )), no?

Read code is better than explanation.

/**
@return Le rectangle delimitant le contour de l'element
*/
QRectF Element::boundingRect() const {
return(QRectF(QPointF(-hotspot_coord.x(), -hotspot_coord.y()), dimensions));
}

/**
Definit la taille de l'element sur le schema. Les tailles doivent etre
des multiples de 10 ; si ce n'est pas le cas, les dimensions indiquees
seront arrrondies aux dizaines superieures.
@param wid Largeur de l'element
@param hei Hauteur de l'element
@return La taille finale de l'element
*/
QSize Element::setSize(int wid, int hei) {
prepareGeometryChange();
// chaque dimension indiquee est arrondie a la dizaine superieure
while (wid % 10) ++ wid;
while (hei % 10) ++ hei;
// les dimensions finales sont conservees et retournees
return(dimensions = QSize(wid, hei));
}

/**
@return la taille de l'element sur le schema
*/
QSize Element::size() const {
return(dimensions);
}

/**
Definit le hotspot de l'element par rapport au coin superieur gauche de son rectangle delimitant.
Necessite que la taille ait deja ete definie
@param hs Coordonnees du hotspot
*/
QPoint Element::setHotspot(QPoint hs) {
// la taille doit avoir ete definie
prepareGeometryChange();
if (dimensions.isNull()) hotspot_coord = QPoint(0, 0);
else {
// les coordonnees indiquees ne doivent pas depasser les dimensions de l'element
int hsx = qMin(hs.x(), dimensions.width());
int hsy = qMin(hs.y(), dimensions.height());
hotspot_coord = QPoint(hsx, hsy);
}
return(hotspot_coord);
}

/**
* @brief ElementScene::toXml
* Export this element as a xml file
* @param all_parts (true by default) if true, export the entire element in xml,
* if false, only export the selected parts.
* @return an xml document that describe the element.
*/
const QDomDocument ElementScene::toXml(bool all_parts)
{
    QRectF size= elementSceneGeometricRect();

        //if the element doesn't contains the origin point of the scene
        //we move the element to the origin for solve this default before saving
    if (!size.contains(0,0) && all_parts)
    {
        centerElementToOrigine();
            //recalcul the size after movement
        size= elementSceneGeometricRect();
    }

        //define the size of the element by the upper multiple of 10
    int upwidth = ((qRound(size.width())/10)*10)+10;
    if ((qRound(size.width())%10) > 6) upwidth+=10;

    int upheight = ((qRound(size.height())/10)*10)+10;
    if ((qRound(size.height())%10) > 6) upheight+=10;

        //the margin between the real size of the element and the rectangle that delimits
    int xmargin = qRound(upwidth - size.width());
    int ymargin = qRound(upheight - size.height());

        // document XML
    QDomDocument xml_document;

        //Root of xml document
    QDomElement root = xml_document.createElement("definition");
    root.setAttribute("type", "element");
    root.setAttribute("width", QString("%1").arg(upwidth));
    root.setAttribute("height", QString("%1").arg(upheight));
    root.setAttribute("hotspot_x", QString("%1").arg(-(qRound(size.x() - (xmargin/2)))));
    root.setAttribute("hotspot_y", QString("%1").arg(-(qRound(size.y() - (ymargin/2)))));
    root.setAttribute("orientation", "dyyy"); //we keep the orientation for compatibility with previous version of qet
    root.setAttribute("version", QET::version);
    root.setAttribute("link_type", m_elmt_type);

Hi again  :-)

Available version 0.35:
   * Now draws reservation teminals in the numeric part. The first placed terminals are not numeric ('-0','R','+1',..) and later the numeric ('1', '3',...). In this last numeric part, the program creates reserve for terminals that are not used.

   * Fixed drawing artifacts while dragging. With hotspot_x=0 and y=0 works, but I leave the same has QET calcs when save from elements editor. The problem was the calc of total size. Now I round to the next tenth and works fine.

Please, check for bugs.

you're welcome.

Script work very well.

I try to test it at office on next days.

Perfect !!

Hi,
any ideas to solve this issue?

One solution is explained at next image.

The other option is to do automatically. Every terminal will sort by:
      First: Only letters: GND, R, S, T,...
      Second: Letters + Number : +1, -0, R1, U1, V1, GND1, ...
      Third: Only Numbers: 1, 3, 7, 33,...

    Inside first group , terminals are sorted alphabetically
    Inside second group, terminals are sorted by the numeric part, and every numeric group by letter alphabetically (GND1,U1,V1,W1)
    Inside third group, terminals are sorted numerically.

I think the second option will be better.

Hi, version 0,4 is available.
Now  terminals names like LETTER + NUMBER, will be sorted as U1, V1, W1 y U2,V2,W2 instead of U1,U2,V1,V2, W1,W2. It makes automatically.

Bah, pour le test j'ai juste collé le script sur le bureau, c'est tout.